The Most Common Reasons for Sump Pump Failure

Sump pumps are an excellent addition to any home. They help avoid basement flooding, protect you from sewage backup, and may even raise the value of your house. They can, however, fail, as do most things. What causes a sump pump to fail is the damage it is supposed to protect your home from. Understanding why sump pump failures might help you avoid them and protect your house.

How Does It Work?

A sump pump’s operation is straightforward. A sump pump is a device that eliminates water from your property and is usually located in the basement. As it fills with water, the pump activates (via electricity) and pushes the water away from the house’s foundation via piping. When the pump fails (frequently submerged in standing water beneath your home), you may be left with contaminated or still water that can damage your foundation and carry disease.

Typical Sump Pump Failures

Sump pump failure may occur for several reasons. Here are some of the most common causes of sump pump failure.

Power Outage

The most typical cause of sump pump failure is a power interruption caused by extreme weather or a storm—your home powers sump pumps, so power outages can be problematic. Since power outages occur randomly, a backup generator is the best method to counteract this.

Inadequate Maintenance

If your pump has stopped working unexpectedly, it needs a good cleaning and quarterly maintenance. To extend the life of your sump pump, you should get it serviced regularly. If your sump pump isn’t operating right now, consider putting a vinegar solution through it and cleaning it out.

A Stuck Switch

A jammed switch is one of the sump pumps’ most prevalent mechanical issues. This issue arises when the pump moves inside the basement, allowing the float to activate the pump. It is also conceivable that some debris may get lodged under the float, rendering it ineffective. This is easily remedied with a bit of cleaning and simple pump adjustments.

Frozen Discharge Pipe

If your sump pump discharge pipe freezes or becomes blocked with debris, water will run back down the pipe and into your basement, resulting in a flood. Although keeping your pipes from freezing is impossible, you may build a specifically discharged line that lets water depart your basement even if the main pipe remains frozen. If your basement floods due to a sump pump failure, contact Bedrock Restoration, and we will gladly assist you.

Poor Installation

Your sump pump is seldom installed incorrectly, but this might be the culprit if you can’t figure out what’s wrong with your pump. Poor installation might cause a variety of problems. These are some frequent installation issues and their solutions:

  • The discharge line’s check valve is not fitted. You’ll hear the pump operating without a check valve, but it won’t be pumping.
  • The discharge line has an improper diameter. Most pumps need a tiny air-relief hole in the line to relieve pressure from the output pipe.
  • The pump is set in sand or gravel. Dirt and gravel may enter your pump, create blockages and damage, and disrupt the float alarm.

Old Age

Years of wear and tear, like other devices, will ultimately lead to the breakdown of your sump pump. A sump pump has an average lifetime of eight to ten years. Although some pumps may last longer, replacing your pump every ten years is suggested to guarantee safety and efficiency. In that case, you always want to start by speaking to your insurance agent about the coverage on your policy.

At Bedrock Restoration, we understand that water damage caused by sump pump failure can be devastating. We provide an experienced team to inspect and assess the damage on your property for insurance claims. Our staff will take detailed photos of the affected areas, creating a comprehensive report with details about the severity of the damage, costs associated with repair or replacement, and the recommended course of action.

What Damages Can Sump Pump Failures Cause

Sump pumps are fantastic tools, but if utilized improperly or without taking the required precautions to avoid failure, you might have a flooded basement and extensive water damage. Don’t be concerned if your house has suffered water damage due to a faulty sump pump. Bedrock Restoration specializes in water damage restoration. Call us, and we’ll dispatch someone to assist with the damage and return your house to normalcy.

With this comprehensive guide, you can learn more about water damage and how to remove the water properly.

Water Intrusion Restoration: What You Need to Know

Water damage may be detrimental to your family’s health and damage your house’s structure. Coping with water intrusion and mold in your house may be a pain, but Bedrock Restoration has you covered. We are restoration and water intrusion specialists, offering complete inspection and extensive repair services.

Improper building techniques, poor materials, weather occurrences, and other factors may all lead to exterior water damage. Bedrock Restoration has considerable expertise in delivering efficient restoration solutions, including damage assessment, pricing estimates, and repair and restoration, regardless of the source.

We can assist you in understanding the process, which includes dealing with builder warranty requirements, legal referrals, insurance claim issues, and other resources like air quality testers and engineers.

Damage Evaluation

The first stage in our water intrusion restoration service is to assess the degree of the damage and decide the next steps in resolving the issue. We can assess the damage and we have the specialized eyes needed to locate any leaks and cracks.

Solution Design and Cost Estimates

The next stage is to analyze the damage and come up with a remedy. Restoration may be used to create a whole new appearance and feel for your property, or it can be used to restore it to its original state. We will meet with you and discuss the possibilities using our design partner’s comprehensive array of goods and services.

Repair and Restoration

This service aims to resolve the underlying issue and return your house to a safe and attractive state. Bedrock Restoration works with skilled contractors homeowners want for a thorough repair and restoration, including removing sheathing, insulation, windows, and other damaged structural elements.

After remedying the underlying issue, we will install your chosen siding solution with skilled, qualified installers. You may relax in the comforts of your own home, knowing that your water intrusion issues are behind you.

Insurance Assistance

A homeowner’s insurance policy often covers water damage. Bedrock Restoration has a long history of dealing with insurance companies and adjusters. After you’ve submitted a claim, we know what information they’ll need to determine damage worth and coverage.

Our on-site professionals will record damage, give thorough repair estimates, and collaborate with officials from your insurance company to expedite the claims process. At the same time, we strive to return your property to its original state.

Free Water Damage or Water Intrusion Restoration Estimate

For any homeowner, water intrusion may be a stressful and costly event. Bedrock Restoration offers the knowledge, resources, and dedication to give you a stress-free solution. Call us immediately for a free estimate, and we will return your house to its original state as quickly as possible. With exceptional customer service and quality work, our experienced personnel is here to assist you every step of the way.

We are looking forward to helping you with your water intrusion repair requirements.

Water From An Ice Dam Is Leaking Into My Home: What Should I Do Now?

It may cause gutters to collapse and shingles to peel off, but you must also worry about inside damage. When ice dam water spills into your home, you must act quickly. How can you keep melting snow and ice out of your attic and around your windows? How might water damage to floors, ceilings, and walls be minimized? That occurs every winter in residences nationwide, particularly in the Minnesota area. We want you to be prepared before anything bad occurs to you. By reading this advice, learn what to do if ice dam water is seeping into your home.

What Is An Ice Dam?

We wouldn’t have ice dams on our roofs if we didn’t need to warm our houses in winter. They begin as thin spots of frozen water on the edge of a roof. The freezing precipitation gathers on the roof during a regular snowstorm. The warmth from the house rises, raising the temperature of the roof’s surface and melting the snow. The internal warmth has little effect on the roof deck above the eaves. Melting snow may freeze when it touches this area of the roof’s edge. The process creates a frozen foundation, which grows and produces an ice dam.

How Do Ice Dams Result In Roof Leaks?

We understand that ice dams cause water damage, but how can they produce a roof leak? Let’s take a brief look at the roof building. The majority of roofs are constructed with 1/2- or 3/4-inch plywood sheathing. A waterproof underlayment covers the lower parts of the roof deck. This barrier rises 2 to 3 feet over the roof’s edge. Typically, the underlayment protects your house from rain and snow, but ice dams create a potentially hazardous condition. It begins with thaw and freeze cycles, accumulating ice along roof edges. The following are some instances of how ice dams form:
  • Icicles that form on roof edges obstruct melting snow drainage.
  • Warm air rises through the attic and melts the snow on the roof.
  • Melting snow backs up beneath roof eaves due to clogged gutters.
These scenarios may prevent melted snow from dropping to the earth from the roof. It instead freezes along the eaves, causing ice dams. When the snow melts and freezes, the accumulating barrier pulls the water back under the roof shingles. The procedure does not take long to drive a snow melt higher on the roof, beyond the waterproof underlayment. When this occurs, the roof starts leaking water into your house. The harm might be significant and perhaps hazardous.

How To Determine Whether You Have Water Damage From The Ice Dams

Water penetrates the home via porous materials and gathers in wall gaps due to backed-up ice dams. It might take many days for the harm to become apparent. Keep an eye out for these indicators of water damage caused by melting ice dams.
  • Sagging gutters or eaves caused by ice dams
  • Water accumulating on the attic ceilings, beams, and joists
  • Water pouring through the attic walls and onto the attic floor, as well as insulation
  • Discolored circular patches appear on the ceilings below.
  • Interior walls with damp streaks under ice dams
  • Moisture buildup around window frames and on window sills
The weather has a role in identifying ice dam deterioration. For example, multiple days of sub-freezing weather might cause apparent evidence of water damage to appear later. When temperatures rise above freezing, the ice dams begin to melt. This latest thaw sends additional water into the home, compounding the previous damage. Check your house for water damage indicators regularly until the ice dam issue is rectified.

What To Do If Ice Dam Water Begins To Leak Into The House

Even the finest ice dam prevention measures might fail at times. The leaks cannot be stopped with a shut-off valve or repaired using a plumber’s putty. These eight steps might assist you in dealing with ice dam backups that cause water to leak into your home.

1. Determine The Location Of The Leak And The Damage

Make your way to the attic and attempt to determine the location and amount of the water damage. Water moves downhill. Thus, leaks on the roof may be several feet higher than they appear on the attic ceiling. Power Tip: Use a powerful flashlight or headlamp to highlight attic ceiling lines and dark nooks.

2. Contact A Water Restoration Company

The damage produced by ice dam water backup within the home is difficult to repair. Soaked walls, damp flooring, soggy ceilings, and leak stains are just a few of the issues you’ll confront. Don’t attempt to handle it on your own. Call in the ice dam water damage experts at Bedrock Restoration—we handle both water damage cleanup/drying and restoration: 612-834-1501 Pro Tip: A skilled water damage repair company should also be able to assist you with filing home insurance claims.

3. [If Applicable] Contact Your Household Insurance Company

Contact your insurance carrier as soon as possible. Give them as much information as possible based on your water damage evaluation. Arrange an inspection with an adjuster, and be sure to get a claims number. Pro Tip: Take photographs of the interiors, significantly impacted sections in the attic, to document the water damage.

4. Attempt To Remove The Ice Dams.

If the weather cooperates and you’re comfortable scaling a ladder, ice dam removal may be a do-it-yourself effort. Nonetheless, many local businesses provide this sort of service. Pro Tip: Before climbing the roof, ensure the ladder’s feet, rungs, and spreaders are securely fastened.

5. Turn On The Fans And Lower The Heat

Set up fans in impacted areas to speed up the drying process. Strong currents of fresh air should be directed over moist floors, walls, and ceilings. Reduce the thermostat setting to prevent heat accumulation in the attic and delay melting on the roof. Pro Tip: Open closets and cupboards near moist walls and flooring below to increase air circulation.

6.  Inspect The Storm Window Weep-holes

If ice dams are forming around windows, ensure the weep holes in the storm window frames are clean. Drill tiny holes between window frames and sill lips to direct leaking water outdoors. Pro Tip: Make weep-hole checks a regular spring and autumn house maintenance component.

7. Key In On The Ceiling

Ice dams may cause water backup into the attic through insulation and ceilings. If you observe water leaking from above light fixtures, act quickly. Be cautious of ceiling bulges as well. Specialists should handle both issues. Pro Tip: Severe ceiling water damage might indicate a probable roof collapse.

8. Continue To Inspect The Roof

Inspect the roof for possible concerns until the ice dams are removed or melted away. Search for areas where the snow has melted. If you notice shingles, look for leaks in the attic below the region. Pro Tip: Get your home’s roof evaluated by a certified specialist twice a year.

Do Ice Dams Damage Roofs?

As the weather improves, the roof’s ice melts, enabling water to flow down. Yet, prolonged freezes and melts cause a dangerous accumulation of ice dams along the eaves. Their size and weight may cause significant issues on the roof, such as:
  • Collapsed gutters
  • Loose shingles
  • Degraded underlayment
  • Compromised roof decking
  • Damaged flashing
  • Structural damage
Fixing a roof after ice dam removal may be a significant undertaking. In severe circumstances, damage to ice dams necessitates partial or total roof replacement.

Are Icicles A Result Of Inadequate Insulation?

Icicles, unlike ice dams, do not back up water into the home, although they often indicate attic concerns. Heat loss through the roof is caused by old, matted insulation, resulting in icicles along the eaves. Inadequate attic ventilation may also cause melting and freezing cycles on the roof. As icicles begin to form on the eaves, you know the circumstances are favorable for the formation of ice dams.

How Can You Get Rid Of Ice Dams Fast?

Use a rubber mallet to break up ice jams, but avoid harming the roof. Calcium chloride crystals may help to accelerate the process. Yet, the discharge may harm nearby plants and trees. A garden hose may be used as an emergency remedy for ice jams. Use it to melt ice dam channels and discharge backed-up water. When temps are above freezing, this temporary remedy works well. Other ice dam removal techniques to consider may be found by clicking here. Remember that breaking up ice dams on a steep roof may be hazardous. If you have second thoughts about taking the job, remain off the ladder. Call a local company that specializes in ice dam removal.

Does Homeowners Insurance Cover Ice Dam Damage?

The expense of eliminating ice dams is not covered by homeowners insurance. On the other hand, water damage caused by leaky ice dams should be covered by your insurance. Water damage to your home’s walls, ceilings, floors, furniture, personal possessions, and objects kept in the attic are all included. Most plans also cover ice and snow damage to roofs. The following external constructions may not be insured for ice dam damage.
  • Fencing and gates
  • Retaining walls
  • Patios and pools
  • Supporting foundations
  • Unattached sheds or garages
If you have any questions concerning your coverage, contact your agent. Inquire about particular water damage coverage, such as interior and exterior leaks caused by ice dams. You may wish to review your insurance coverage for your home and goods.

7 Effective Ways To Prevent The Formation Of Ice Dams

Ice dams will always be a source of frustration for many homeowners throughout the winter. A little forethought before our next snowstorm can go a long way. With these seven ice dam avoidance methods, you can reduce the likelihood of damage to your house.

1. Keep Inside Warm Air

Ensure that the attic is as airtight as feasible. Edges surrounding pipe vents, fittings, and electrical outlets should be sealed. Don’t forget about the spaces surrounding the ceiling rafters and joists.

2. Improvement Of Attic Insulation

Old insulation allows warm air from below to enter the attic. The warmth rises, melting the snow on the roof. Updating old insulation improves ice dam prevention measures while lowering heating expenses.

3. Clear Vents And Soffits

When these roof devices get clogged with debris, they cannot perform their functions. Filthy soffits and vents also delay the flow of melting snow off the roof, which leads to ice jams.

4. Clean Downspouts And Gutters

When the roof drainage system fails, the danger of ice dams increases considerably. Maintain gutters and downspouts clean to manage drainage from snow melting on the roof.

5. Rake The Roof

Snow removal from the roof reduces the cause of ice dams, but proceed cautiously. Check the condition of your ladder and utilize a suitable roof rake that will not harm shingles or flashing.

6.  Do Not Allow Roof Valleys To Clog

As leaves and twigs accumulate in a roof valley, the material slows the flow and contributes to water freezing on the roof’s edge. Check and clean these places regularly.

7. Think About Heat Cables

These devices have the potential to be highly useful in avoiding ice jams. They are also suitable for usage within downspouts. Install heat wires that are mainly intended for usage on the roof.

Do You Have An Ice Dam Roof Leak? We Are Here To Assist!

Call Bedrock Restoration if water has entered your house due to an ice dam. We provide emergency ice dam repair services. Our expert specialists can remove ice dams, repair roof leaks, and repair interior water damage caused by ice dams swiftly and safely. Other home renovation services we provide include attic insulation, wood rot treatment, and gutter installation. Call us now for additional information or to set up an appointment. Our professionals are here to assist you!

Frequently Asked Questions About Ice Dam Water Leaks

How much does ice dam water damage repair cost?

The water damage to the interiors and goods determines the cleaning and repair cost. Repairing ice dam water damage may cost anywhere from $1,500 to $5,000, with an average cost of $3,000. This does not include the expense of expert ice dam removal.

Who do I contact if I have ice dam water damage?

Contact a water damage repair firm specializing in ice dam cleaning and restoration. Bedrock Restoration’s employees are industry-certified and have extensive expertise in this field. We can also assist you in filing an insurance water damage claim.

Do ice dams usually cause property damage?

Ice dams cause melting snow to back up beneath the roof and into the walls if not maintained. Water rots internal wall frames and soaks the attic, destroying roof decking and rafters.

How can I securely remove ice jams from my roof?

Let an expert handle the situation. You can clear accumulated snow using a roof rake and push broom, but it’s better to have an ice dam removed by a qualified specialist.

What is the best way to melt ice blockages in my gutters?

Fill the open end of a pair of pantyhose with an ice melter and fasten the open end. Set it up to cross the ice dam and hang over the gutter. This method melts a channel used to drain backed-up water.

When should I hire a professional to remove ice jams from my roof?

Call a roofing specialist if: the ice dam accumulation is substantial; your attempts to remove the ice dams are unsuccessful; water damage inside is expanding fast; or, most critically, you don’t feel secure doing it yourself.

Basement Moisture: Causes and Solutions

This article briefly explains moisture sources, moisture movement methods, and common basement moisture concerns. Finally, a step-by-step procedure is described for each issue and numerous specific alternatives to fixing the problem.

An Issue That May Harm Your Health and Your House

Moisture issues in existing basements are fairly prevalent but often misunderstood and undertreated. This may not be a big issue in a seldom utilized basement and isolated from the living quarters above. Most basements, however, are linked to the rest of the home by ducting or other openings. Moreover, basements are increasingly being converted into completed living and sleeping areas. Moisture problems are not only bothersome and uncomfortable in these circumstances but may also lead to health issues. Mold and mildew may develop in moist carpets and behind wall coverings. Basement water issues are treatable, but they come at a cost.

Understanding the Issue

To resolve basement moisture issues, it is vital to first determine where the water is coming from and what processes allow it to enter the basement. There are just three moisture sources:
  • Rainwater or groundwater liquid.
  • Humidifiers, unvented clothes dryers, restrooms, and stoves, as well as moisture in concrete after construction, are examples of interior moisture sources.
  • Humid air from the outside enters the basement and condenses on cold surfaces.
Four systems transmit moisture from the exterior of the structure to the inside of the basement:
  • The flow of liquid water.
  • The suction that is caused by capillary action.
  • Diffusion of vapor.
  • The movement of air.
Poor construction with cracked, sinking foundations is also blamed for difficulties. Houses and basements may be physically solid in many circumstances, but they are often not equipped to manage water drainage. It is typical to fail to slope the ground surface away from the foundation or to lack a sufficient gutter and downspout system. Subsurface drainage systems that are either missing or inoperable are also rather common. These issues may be addressed and rectified if a systematic method is utilized. This article briefly explains moisture sources, moisture movement methods, and common basement moisture concerns. Finally, a step-by-step procedure is described for each issue and numerous specific alternatives to fixing the problem.


  • Water seeped through the walls.
  • There is standing water on the floor.
  • A damp ring surrounds the saturated foundation of concrete block walls.
  • The air is damp and humid.
  • Summer condensation on cool walls and floors.
  • Mold, mildew, and odor.
  • Carpet or wood deterioration.
  • Rot and deterioration of wood headers, joists, sill plates, and columns.
  • Wall covering staining and blistering.
  • Spalling of concrete or masonry due to efflorescence.

Sources of Basement Moisture

Groundwater and Rain

A 1-inch rain drops 1,250 gallons of water on a 2,000-square-foot house’s roof. Some water enters the basement due to improper grading, gutters, and downspouts. Flooding or seasonal site conditions may also cause the below-grade water table to increase. This is why drain tile systems are advised around basement walls, even on sandy or gravel soils.

Sources of Interior Moisture

People and their actions cause moisture within basements. Humidifiers, unvented clothes dryers, bathing, and cooking are all common causes. These operations expand once basements are completed. Another internal source is the moisture contained in fresh concrete after construction. This may equate to 0.2 gallons per square foot of the wall and 0.1 gallons per square foot of floor in a normal home. A new property may take months or even years to settle into its surroundings.

Ventilation with Humid Outdoor Air

Basement windows can be opened for fresh air in the summer. If the air outside is warm and humid, it will condense on the chilly basement walls and floors. Many people detect this dampness and feel they have a basement wall leak when, in reality, the moisture comes from condensation.

Moisture Movement Mechanisms

Capillary Suction

Moisture is moved through porous materials via capillary suction. Water may be carried upward and laterally via microscopic pores in the concrete footing and slab. This action causes a damp ring at the foot of many basement walls. This is quite prevalent in cold joints. Water may rise substantially due to capillary pull, as seen below: The kind of soil and the degree of capillary rise:
  • Gravel – A few inches or less.
  • Sand – 1 to 8 feet.
  • Silt – 12 to 16 feet.
  • Clay – 12 to 20 feet.

Air Leaks Through the Walls and the Floor

Warm air rises and causes a stack effect in most homes. This creates a negative pressure in the basement and pulls wet air in via foundation cracks or holes, including open sump pits. As a result, sumps should have an airtight lid. Moist air is pulled through the block cores of a concrete block foundation, particularly if they are left exposed at the top course.

Diffusion of Vapor Through Foundation Walls

The transport of moisture in the vapor state through a substance is called vapor diffusion. It is determined by the material’s permeability and the driving power of the vapor pressure difference. Vapor may flow from wetter ground to drier basement interior via concrete walls and flooring in a basement. This process is slowed by vapor retarders such as foundation waterproofing and polyethylene.

The Most Common Causes of Basement Moisture Issues

Insufficient Grading

Problem: Water is channeled into the basement if the land surrounding a foundation is flat or slopes toward the house. The soil next to the home is often backfilled without sufficient compaction and eventually sinks. This is particularly true under stoops, where water may gather against the basement wall. Solution: Put soil around the house on a slope of at least 1 inch per foot away from the foundation wall for at least 6 feet.

Defective or Missing Gutters and Downspouts

Problem: Defective or missing gutters and downspouts drive rainfall toward the foundation perimeter. A downspout that lacks an extension or splash block is worse than none. It collects massive rainfall from the roof and deposits it in a single concentrated spot near the basement. Solution: Install at least one downspout for every 50 linear feet of a roof eave. Water should be discharged at least 4 feet beyond the wall. Rain drainage is effectively directed by slanted concrete walkways surrounding basements.

Inadequately Built Window Wells

Problem: Window wells function as a drain close to the basement wall. They are often designed incorrectly, directing any water toward the base rather than away from it. Solution: Window wells should be filled with 3/8- to 3/4-inch coarse aggregate from the footing to the window sill. A supplementary drain tile extension should be installed from the footing to the base of the window well.

The Drain Tile and Sump Pit Are Ineffective

Problem:  Many current homes lack a subsurface drainage system. This dates back to when basements were not utilized as living spaces. In other circumstances, the systems fail for reasons like pipe collapse, silt and/or tree root clogs, or a damaged connection to the sump. A pump is frequently installed in the sump pit to move the water to the ground surface outside the foundation wall. This pump has the potential to fail. Solution: See the methods 2–5 that follow.

Inadequate Drainage With Under-Slab Ducts

Problem: When heating ducts are put under a basement floor slab, the drainage system may be constructed at a height that is too high. In effect, the duct functions as a drainage system. Mold infection might have major health repercussions if standing water is inside the heating duct. Solution: Heating ducts installed under the basement floor must be insulated, waterproof, and sloped to drainage and cleaning stations. Under the ducting, a drain tile and coarse aggregate may be installed.

Structural Cracks

Problem: Cracks in concrete and concrete block foundations are common. These may be severe if the floor joists are not correctly linked to the foundation wall, allowing the wall to shift. Cracking is sometimes caused by soil settling. Cracks are common when walls meet solid constructions, such as a fireplace. Drainage usually eliminates water from fractures, although maintenance may be required. Solution: Appropriate footing design is necessary, as is a correct link between the foundation wall and the building above.

A Basement Moisture-Resolution Options Overview

The easiest way to handle any construction challenge is to start with simple and low-cost solutions. Next, in a logical sequence, do the next least expensive procedure with the highest likelihood of success. When dealing with moisture issues, the best technique is nearly always to eliminate or regulate the source of the moisture rather than trying to stop it at the final line of defense. Initially, and least expensively, eliminate excessive internal moisture sources in the basement (humidifiers, cooking) and ventilate other sources (clothes dryer, bathroom). Second, if condensation is a problem in the summer, avoid immediately ventilating the basement with warm, humid air. Using an air conditioning system or a desiccant-type heat exchanger for ventilation is advisable.

Dehumidification Isn’t a Long-Term Solution

Dehumidification may help reduce the symptoms of humidity and odor in a basement, but it is not a long-term or perfect solution. Using a dehumidifier in a basement with moisture issues may do more harm. Moisture is pulled into the basement more quickly when the air is dried out, producing efflorescence and spalling of concrete and severe damage to interior finishes.

Interior Membranes or Coatings Are a Short-Term Solution

Remaining a basement moisture issue with an internal membrane or coating is enticing. It is less costly than a drainage system and seems to function in certain circumstances. Nonetheless, the water remains, and these systems fail or redirect the water to another passage into the basement.

Recommended Strategy

Assess gutters, downspouts, and surface grading: After eliminating indoor moisture sources, the suggested procedure is to check the gutters, downspouts, and surface grading surrounding the home. These should be addressed first since they may resolve the issue. Interior or exterior drainage system: If the moisture issue continues, an interior or external drainage system should be installed. All of these methods are detailed further below. If you want to complete a basement with water difficulties, you must first deal with the water problem. Sub-slab depressurization system: An active depressurization system with a washed-rock layer under the slab is advised. This pulls wet air from under the slab, which may assist in lessening the amount of moisture vapor entering the residence via slab holes. It also aids in the management of radon and other soil gasses. Sumps and other exposed soil connections outside the foundation and under the slab should be plugged and sealed.

A Step-by-Step Procedure

  • Control the sources of indoor moisture.
  • Avoid using outdoor air for ventilation during the summer.
  • Proper grading, guttering, and downspouts.
  • Install a drainage system, either inside or outside.


  • A dehumidifier may help alleviate the symptoms of humidity and odor, but it will not address the issue.
  • A membrane or coating on the inside that does not provide drainage will not fix the issue in the long run.
  • Before insulating, the walls must be dry. Before carpeting, the slabs must be warm and dry.

Approach 1: Build Adequate Gutters and Downspouts, As Well as Suitable Grading

Many basement water issues may be avoided by correctly managing rainfall and surface drainage by installing gutters and downspouts with extenders or splash blocks to direct water away from the foundation. It is critical to slope the gradient away from home, which may need bringing fill to the site. Before installing any below-grade drainage system, this should be done since above-grade modifications may address the issue. Even if a drainage system is needed, draining water as much as possible at the source is essential.

Approach 2: Outside Drainage System

Putting an outside drainage system on an existing structure is the most expensive and effective water management method. This entails excavating the area surrounding the foundation and reconstructing it like a new home installation. Digging up plants and other barriers surrounding the home is also required. Waterproofing and insulation are often completed concurrently, along with any structural repairs. Backfill for classic outside drainage systems is free-draining sand. Drain tile may be installed next to or on top of the footing. The installation of level drain pipes is good. Around the drain tile, a minimum of 12 inches of coarse aggregate should be used. Transporting pea rock or sand to a location for backfilling might be costly. Instead, a drainage mat may be laid against the foundation wall and then backfilled with whatever soil is available. The drainage must flow freely to the perforated drain pipe below.

Approach 3: Above the Concrete Slab, There Is an Inner Drainage Canal

When water enters the basement, an internal drainage system is usually constructed. A drainage canal attached at the base of the wall and the floor slab is the simplest and least expensive solution. Water is collected and drained into a sump basin through another channel installed on top of the slab, then via a trap. The sump should be airtight and childproof. This method is best suited to a cracked concrete wall. It does not address the issue with masonry walls since the water stays in the block cores at floor level, and the water level is only decreased to the top of the slab. The water is not evacuated from the area using this method. Consequently, humidity, mold, and mildew may still be an issue. This technology is unable to drain groundwater from under the floor slab.

Approach 4: Inside the Slab Edge, an Inner Drainage Channel

Another method is to install a drainage channel on top of the footing at the base of the wall. This necessitates the removal and replacement of the concrete around the slab border. The drainage channel is linked to a pipe that leads to the sump. The sump should be airtight and childproof. Since it thoroughly drains the block cores, this method is useful for concrete masonry walls with water issues. To allow for drainage, holes must be bored at the base of each block core. This may need removing more concrete than the minimum quantity specified to fit the drill. Depending on the product fitted, these systems come in various forms and pricing. Since moisture is permitted to permeate the block cores, it is critical to cover the tops and coat the inside basement walls with a vapor-retarder coating.

Approach 5: Underneath the Slab Internal Drainage System

A perforated drain pipe put within the perimeter of the footing is the most efficient internal drainage system. This necessitates the removal and replacement of concrete at the slab border. The drain pipe is placed under the slab to drain the area to a lower level. The drainage pipe, like an outside system, links to a sump. The sump should be airtight and childproof. The dimpled plastic sheeting put at the base of the wall and under the slab edge is a significant component of this strategy. Dimpled sheeting looks like a little egg crate and allows for unimpeded draining of the wall into the drain pipe. It costs less than many specialist drainage channel solutions. This method cannot handle increasing groundwater in poor permeability soils unless an aggregate layer is underneath the slab. This solution should be supplemented with an active soil gas management system that links to the sump and perimeter drain pipe.


The moisture in a basement is complex and can be caused by a variety of factors. The solutions discussed here may help to reduce the amount of groundwater collected around the foundation wall and floor slab. Still, it’s essential to understand all contributing factors to identify the root cause effectively. A comprehensive assessment helps ensure the best remedy for your particular situation. Bedrock Restoration can provide a detailed inspection of your basement and make the necessary repairs to ensure it is dry and safe for you and your family. Contact us today to get started!

Sump Pump Failure: What to Do

A flooded basement or sewage backup is not a pleasant experience! What’s worse is when your sump pump fails to function correctly. With the rainy season coming, you should double-check that your pump is performing as intended. We strongly advise you to take the necessary precautions to avoid future failure. Nevertheless, if it is too late and your sump pump begins to malfunction, read more at Bedrock Restoration to find out what you can do! If the condition worsens, you may need an expert to fix it.

Signs of Sump Pump Failure

There are many reasons for sump pump failure, and you want to do all you can now to avoid it. Also, you always want to start by speaking to your insurance agent about your policy coverage to ensure you are protected in the event of failure. Our team can assist you in talking to your insurance provider and helping you with the best solution if your sump pump fails. We strongly advise hiring a professional or purchasing a new sump pump. Doing so immediately rather than spending hundreds of dollars on water damage later is preferable. So, what are the warning signs? If your sump pump falls into any of these categories, you should have it fixed before the problem worsens:


A blocked pump is the most common cause of sump pump failure. Hence it is critical to eliminate the blockage as soon as possible. We strongly advise that you keep an eye on your pump regularly to avoid any buildup of dirt or debris.

Strange Sounds

The more noise from the sump pump pit, the more complex the situation. The motor on your sump pump will stop working as it ages. A rattling motor is an indication that your sump pump is deteriorating.

Your Pump is Getting Older

If you’ve had your pump for seven years, it’s probably time for a replacement. Looking for rust is the easiest way to know. This will assist you in determining when to replace your sump pump. Visible rust in the motor might lead to chemical buildup and, in extreme cases, block your pump.

Constant Flooding

A sump pump’s primary function is to keep your basement from flooding. If you discover your pump is not performing its function of avoiding floods, you have a problem. Let’s get things handled as soon as possible to prevent a much bigger hassle in the future. Before considering obtaining a new one, you may take a few measures.

What Should You Do If Your Sump Pump Fails?

The more constant you are with sump pump maintenance and checking on it, the longer it will survive and prevent failure. But, if it is too late and you suffer floods, you must act quickly. Taking the water out yourself may seem more cost-effective, but we do not suggest it. It is advisable to hire a professional who has the necessary tools and safety equipment to do the work. If the flooding is not too threatening, you may try to repair the source of the water damage and do what you can to dry out the area to avoid mold growth. When your pump malfunctions, follow these steps:

Avoid Clogging

Clogs are the most typical reason for your sump pump failing. You must do all possible to avoid this from occurring. Open the pump lid regularly to inspect for debris and small household items. Cleaning and replacing clogged filters might help the pump last longer.

Examine the Power Source

Power outages are likely during a stormy season. Ensuring your sump pump is constantly powered will keep it from failing. Check your backup battery system regularly and ensure the wire is always connected to an outlet.

Look For Leaks

Indications of outside water or leaks in the discharge pump might assist in determining if replacement or repair is required.

Replace Malfunctioning Float

If filling the sump pit with water is not causing the pump to turn on and off, then this might suggest the defective float has to be replaced.

Fix Your Sump Pump

If the sump pump isn’t too badly broken, you may be able to repair it. It is essential to evaluate the damage first and do everything you can to establish an insurance claim. You want to avoid walking in there and aggravating the situation if you know what to do.

It’s Time to Get Help from the Experts!

Attempting to fix your sump pump on your own might be quite inconvenient. Making it your DIY project might make matters worse if you don’t have the necessary equipment and skills. When water enters your house, it may be quite challenging to remove. That is why our Bedrock Restoration team is here to assist! We recognize that homeowners often confront several risks to their property. We are here to take on problems and give you the pleasure of security, regardless of the danger. Contact us today to get the quality service you deserve.

What Are the Benefits of Hiring a Qualified Water Damage Restoration Company?

Working with a skilled water damage restoration business has a number of advantages. Most importantly, it guarantees that a terrible situation is not exacerbated. After a flood, professional water damage restoration makes containment, cleanup, and restoration easier. Having a competent business assist you with flood damage ensures that the job is done correctly. It’s an investment in your home or business that avoids a lot of long-term upkeep and health problems. You’ll have peace of mind knowing that you’ll get through cleanup rather than just dealing with the evident damage. Remember that water damage can lead to a slew of other problems. It creeps into cracks and crevices, soaks through carpeting and flooring, and serves as the starting point for mold growth. Having a professional examine the problem and thoroughly resolve it saves you a lot of time and trouble in the long run. The following are some of the advantages of hiring a professional water damage restoration company:

Immediate Response and Speedy Service

Most water damage restoration firms, like Rapid Dry, have emergency services available. We realize how critical it is to act swiftly in the event of water damage. Our prompt reaction guarantees that the drying and cleanup activities begin as soon as possible.

Expert Guidance

You can manage a water damage emergency on your own, but you’re asking for trouble. Having an expert guide ensures that the job is done correctly and that you do not end up with major long-term complications. A full cleanup plan is required following flooding, which is provided by a professional water damage restoration firm.

Access to State-of-the-Art Equipment

There are numerous methods for drying out after water damage, but DIY treatments tend to prolong drying time. When you contact a professional water damage repair firm, you will get access to equipment that expedites drying time and allows you to return to your normal life as soon as feasible.

Safe Cleanup

One of your main concerns following a flood is contamination and how it can harm your health. You don’t need to endanger your loved ones when you’re already coping with flood damage. A competent water damage restoration firm understands the risks that follow water damage and can act to eliminate those concerns as soon as feasible.

Lessen the Damage Impact

It is an investment to hire a professional water damage restoration business after a flood. It keeps future losses at bay and helps you to rebuild your house as quickly as possible. If you do not contact a professional after a flood, you may end up paying more in the long run and creating an even worse problem than you already have. One of the wisest things you can do after a flood is to contact a professional water damage restoration business. It can save homeowners’ insurance companies time and money by ensuring that the cleanup and restoration operations are done appropriately. If you have any questions about how a professional water damage restoration business can assist you, or if you have a flooding emergency and require immediate assistance, call Bedrock Restoration at 612-834-1501.

How to Prepare A Vacant House For The Winter Months

One of the most important things you can do to prepare your home for the winter months is to winterize it. This means taking steps to protect your home from the cold weather and the potential damage that can come with it.

Turn off the main water supply to the home

If you have a second home, care for a vacant home, leave for an extended vacation, or just want to know how to avoid frozen pipes, then here are a few simple steps to winterizing a vacant home! This will protect your home from frozen pipes and potential water damage. If you’re not sure how to turn off the main water supply, your local water utility can provide instructions. It’s a good idea to label the shut-off valve so you’ll know where it is in case of an emergency.

Drain the pipes of all water

This will help prevent your pipes from freezing and bursting in the cold weather. There are a few simple steps you can take to drain the pipes:
  • Open all sink faucets
  • Open lowest sink in lowest level of the home
  • Open tub & shower faucets
  • Flush all toilets
  • Leave faucets in open position
This should help prevent any water from freezing in the pipes and causing damage. If you are unsure about how to drain the pipes or if there is a problem, contact a licensed contractor for assistance. When the cold weather starts to creep in, it’s important to take some precautions to protect your home. One such precaution is winterizing your plumbing. This involves pouring non-toxic antifreeze into your toilets and drains to prevent them from freezing up.

Pour non-toxic antifreeze into toilets and drains

Antifreeze is a great way to keep your plumbing functioning properly during the winter months. It’s nontoxic, so it’s safe for both you and your pets, and it’s easy to use. Just pour it into your toilets and drains, and you’re good to go!

Protect outside faucets and spigots using covering

One important step is to winterize your outside faucets and spigots. This can be done by using a covering to keep the water from freezing. There are a few different types of covers that you can use. One option is an insulated cover that fits over the faucet or spigot. This type of cover is made of foam and is designed to keep the water from freezing. Another option is a plastic cover. This type of cover is less expensive than the insulated cover, but it does not keep the water as warm. You can also use a heat tape to winterize your faucets and spigots. A heat tape is a piece of electrical wire that wraps around the faucet or spigot. The wire warms up and helps prevent the water from freezing. No matter which type of cover you choose, it’s important to make sure that it fits tightly over the faucet or spigot. If the cover is loose, it will not do its job in keeping the water from freezing.

Adjust the thermostat

Winterizing your home means adjusting the thermostat to save on your energy bill. One way to do this is to make sure your home is properly insulated. Installing a programmable thermostat can also help you save energy by adjusting the temperature to around 55 to 60 degrees. By making these small adjustments, you can save a lot of money on your energy bill this winter. Now that we’ve gone over some tips on how to prepare a vacant house for the winter months, it’s important to remember that these are just general guidelines. Every property is different and will require its own specific care and attention in order to protect it from the cold weather. If you’re not sure what to do or need more help preparing your property for winter, be sure to contact Bedrock Restoration at 612-834-1501. We will be able to give you tailored advice and assistance based on your individual needs and situation.

5 Ways to Prevent Pipes From Freezing

If you’ve ever had a flooded basement due to a frozen pipe, you understand how critical it is to keep pipes from freezing. Even the best-insulated pipes can freeze in single digit and subzero temperatures. When temperatures fall below freezing, uninsulated pipes are at risk. When the pipe freezes, it builds pressure that causes fractures or breaks, and when the water thaws, it explodes from the freshly created crack, flooding your home. Unattended, a burst pipe can flood your basement and cost tens of thousands of dollars in damage to your property. The good news is that there are methods for protecting your pipes from freezing temperatures. You won’t have to worry about cracking, popping, bursting, or a flooded basement if you keep your pipes and the water in them above freezing. What are the top five things you can do to keep your pipes from freezing?
  1. Run the Heat 
If the house is empty and you’ve turned off the heat to save money, now is the time to turn it back on. One of the greatest methods to keep temperatures high enough to prevent frozen pipes is to leave the heat on when the house is empty. Homes that are occupied full-time can keep the heat on as usual, though an extra degree or two when temperatures fall below zero won’t hurt. However, if you’re going on a winter vacation or if the house has no current residents, make sure the heat is kept at a minimum of 50 degrees during the colder months. This avoids freezing and ensures that you do not arrive home to a flooded basement.
  1. Drip the Faucet
Keeping the water in the pipes circulating decreases the risks of freezing. Allow a tiny trickle from any faucets connected to potentially troublesome pipes. This will not keep the pipe from freezing, but it will keep it from exploding since it lowers pressure.
  1. Open Cabinet Doors
If your house is like many others, you have pipes hidden beneath cabinets. When the temperature drops, open these cabinet doors to allow heat from your home to reach the pipes.
  1. Install Heating Tape
When temperatures drop, heating tape wraps around pipes and keeps them warm. You can choose between tape that automatically turns on and off and tape that connects into an electrical socket. This method works well for tiny pieces of pipe that are at high danger of freezing. A professional should install heating tape to ensure it is used safely and is not in contact with combustible materials.
  1. Increase Insulation
When it’s cold outside, insulation is your home’s best friend. If you have pipes in an area that isn’t very well insulated, it’s a good idea to add more insulation to keep them from freezing. To keep your vulnerable pipes warm, many forms of insulation can be fitted around them. An expert can advise you on the best type of insulation for your needs and ensure that it is correctly placed. Finally, keep in mind that residences in cold climates are not the only ones at risk of freezing. In reality, homes in warmer climates often lack the insulation needed to withstand the occasional cold snap. Regardless of where you live, it’s a good idea to have your pipes examined so you know they’re adequately protected and you don’t have to worry about freezing, bursting, or flooded basements. If you need further cold weather advice or need to speak with someone about a busted pipe or flooded basement, call Bedrock Restoration at 612-834-1501

Cleaning Up Water Damage After a Pipe Bursts

Water damage and restoration firms get a lot of calls regarding busted pipes and floods this time of year. Pipes that aren’t properly insulated are vulnerable to freezing and rupture when temperatures drop. And, if you live in a cold-weather area, the risk of freezing occurs even if your home and pipes are well-insulated.

What Makes Pipes Burst?

Though freezing temperatures are the primary cause, the science of burst pipes is mainly concerned with ice and pressure. Because ice has a greater volume than water, when water inside a pipe freezes, it expands and causes pressure. The pressure builds up until the pipe splits or bursts. If the water thaws or any unfrozen water reaches the damaged location, it can only travel one way: out the pipe. Turning on faucets helps prevent bursting and flooding because it reduces pressure, so even if the water freezes, there will be no serious flood damage.

What Should I Do If a Pipe in My House Bursts?

The first thing you should do if you see a frozen or burst pipe is to turn off the main water supply. This minimizes floods because no water will enter your home. The next step is to contact a professional restoration firm. If you are unsure where the problem occurred, they can locate it and perform any necessary repairs. Most restoration businesses have plumbers on hand who can be called promptly if necessary. It is critical to remember that you should not enter a flooded area until you are certain it is safe and there is no risk of electrocution. If flooding occurred as a result of your failure to recognize the problem in time, you will need to deal with a professional restoration firm for assistance with cleanup.

What Are the Advantages of Hiring Professionals to Repair a Burst Pipe?

The most obvious reason to call in professionals when a pipe freezes or bursts in your home is so that the situation may be resolved as soon as possible. Your goal is to avoid harm as much as possible and to repair any damage that does occur as soon as feasible. Professional restoration firms can assist you with this. You can get help from restoration businesses with:
  • Determining the exact location of the burst pipe and the extent of the damage to your property
  • Using professional equipment to determine the water’s course through your property
  • Identifying water-damaged surfaces in your home, such as ceilings, walls, flooring, fixtures, and mechanical issues
  • Determining the best strategy for cleanup and restoration

Can I Repair a Burst Pipe Without Professional Assistance?

After a pipe bursts in your home, you may be tempted to do your own cleanup and restoration, but this can be a costly error. Remember that simply drying out the space and replacing any damaged carpeting or furniture is not enough. Surfaces must be thoroughly cleaned, and an inspection must be performed to ensure that mold and other risks are not present. Professional water restoration businesses also have the skills and equipment to complete the job correctly the first time, which can save you a significant amount of money in the long run. To assist you with floods and water damage, restoration companies employ a range of tools, including:
  • Dehumidifiers
  • Air transporters
  • The heating system
  • Cameras for thermal imaging
  • Meters for measuring humidity
  • Systems for drying wood floors
  • Dehumidifiers with desiccant
  • Antimicrobial treatments
  • Water extraction systems
  • Drying in the wall cavities
Following a flood, restoration companies provide a complete service plan that ensures your home is properly cleansed and free of pollution. If you have a busted pipe or need assistance after a flood, call Bedrock Restoration at 612-834-1501.

Centennial Lakes Park

Centennial Lakes Park is a beautiful oasis in the heart of Edina. The park spans over 24 acres and features a variety of activities, including paddle boating, mini-golf, biking, and a cutting course. Centennial Lakes also offers a wide variety of amenities for residents and visitors, such as a playground, picnic areas, and a beautiful environment. There are plenty of things to do at Centennial Lakes Park, making it the perfect place to spend a day or afternoon.


Centennial Lakes Park is a 24-acre park and artificial lake with just under two miles of beautiful paved walkways interspersed with beautifully landscaped grounds, seating areas, benches, and fountains. The park is open from dawn until dusk and is free to the public. With a relaxing and fresh vibe, this park is the perfect place to spend a day or afternoon. Centennial Lakes Park offers plenty of family and fun activities for visitors. For example, the lake offers fishing, canoeing, kayaking, and paddleboat rentals. Visitors can enjoy fishing, bird watching, or a leisurely walk around the lake.

Entertainment & Events:

From June through August, live cultural performances take place at the Centennial Lakes Amphitheater at Centennial Lakes Park. Movies in the Park are shown on Thursday evenings during the summer. The park also offers fishing opportunities and hosts special events throughout the year. Centennial Lakes Park boasts the perfect spots to host corporate outings, team-building weekends, strategic planning sessions, or business meetings. One can also rent space for their wedding as the park offers all the services needed for a special day.


Visitors can do various fun activities like renting out paddle boats, fishing in the ponds for sunfish, bass, and bullheads, or watching remote-controlled sailboat races. They can also explore the maze, and try their luck on the bent grass-putting course or lawn bowling lanes. With plenty of activities to keep you busy, the park is a great place to spend a day or afternoon. You can enjoy a walk or bike ride around the lakes, paddle around in a boat or kayak, try out the playgrounds and picnic areas, or take in a game of golf.

In conclusion, Centennial Lakes Park is a wonderful place to relax, have fun, and connect with friends and neighbors. The park is full of activities to keep you busy and happy. The park also hosts special events throughout the year that can help you connect with your community.


The Southdale Center is an iconic shopping center in the Minneapolis suburb of Edina, Minnesota. The center was built in 1956 and was the first shopping center in the United States to be fully enclosed and climate-controlled. It is also one of the largest shopping malls in the country, featuring over 200 stores and restaurants.